• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

What did you do with your Scrambler today? August 2013 version

Status
Not open for further replies.
I wonder how different is a 70 brake system from a 72? The shoes are the same 66-75 so I wonder if this might fit;
http://www.quadratec.com/products/56208_0001.htm

The way I understand it, my set up was only used in 70-71. I have notes somewhere, but if my memory is right I've got 10" drums. I replaced just about everything a few years ago, but we weren't able to get the bars then, either. There is a metal shop a few towns over, so I'm thinking I'll head there and see if I can fab something together. These are straight, so it shouldn't be too bad. As long as the right side is still intact so I have a pattern to work with.
 
Not the scrambler (thats still in many pieces) but dragged the CJ6 to an off road weekend and had a good time with my two sons and some friends (despite the rain:().kirton1.jpgkirton2.jpg
 
Thought about putting the soft top back on...we got about 3" of rain in the last couple hours...


Naaaah...it'll stop.

By tomorrow, I hope- I have to drive 30 miles for my job.
 
Ok my baby is coming back home. :headbang: Had a 4:1 Lowmax put in, got the trannie checked out (more on that later) and some drive shaft work. All it needs is some plumbing (new SS tran lines), couple of UJoints and work out the remaining gremlin in the Howell setup then its ready for our little group's annual pilgrimage to Colorado. 9 day of wheeling around...

Oh...and the top arrives tomorrow. Tigertop since I couldn't pass the BD top by the CFO. I wanted full soft doors anyway which would have made the BD top an $1800 top. They are not the ideal soft doors but most times I'll just leave it in the back anyway.

spacergif-1.jpg
 
Took the Scrambler on my junkyard run. But first, we stopped by the local Habitat ReStore, and I picked up 8 high intensity 3 tube fluorescent fixtures for $40.00! I'll have some shop light now...

IMG_0489.JPG

Then on to U-Pull-It. I was looking for a steering box to mock up my MORE 1" forward box mount on my spare frame clip. Got the box, but found a lot more that I couldn't bring home...

A 75 J10, with Woodgrain sides, ""Pioneer" on the rear quarters. Great body, no rust, engine parts missing. Why???

IMG_0484.JPG

A 65 J10, little beat up in the front, but again- hardly any rust, a good restoration candidate! Why do people scrap these?

IMG_0486.JPG

Next, a little Scout. This one was beat, but it's twin brother in great shape was in the holding area, awaiting it's turn at the hands of the vultures....

IMG_0485.JPG

A 51 Plymouth? In the scrap yard? Also with no rust? Really?

IMG_0487.JPG

If I could of, I'd have brought them all home. And, on the way out, the guy at the counter tells me they just had a clean 74 VW Bus and a clean 69 VW Beetle go straight from holding to the crusher... Why, oh why...:banghead:

And, I found these laying in the bed of a truck by a driveshaft, so I grabbed them. I was thinking they might be OEM aluminum u-joint saddles, but on closer inspection I think they're bearing caps off an A/C compressor.

IMG_0490.JPG
 
Last edited:
Sweet !!
How much did that cost you ??

Around $500 with the cost of gas and tolls. But it does match my current gearing, so short term saved a little on not having to re-gear immediately, but long term I'll have two diff's to re-gear.
 
A&W drive in after an oil change, brake light switch replacement, a recycling/beer run, and a trip to the hardware store for a fitting I need for Mater.

ImageUploadedByTapatalk1377978056.814695.jpg
 
Looks like a vent control or a hand control used when delivering mail for a sign or something.

Karl
 
Status
Not open for further replies.
Back
Top