• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Which engine would you go with

onesourcemike

CJ-8 Member
Gold Member
City
Wilmington
State
NC
Was thinking of putting a v-8 in my scrambler. If you could pick the perfect motor what would it be. I was thinking of purchasing a 350 from summit and then what transmission would you have. I have a SR-4 now and I'm sure it wouldn't last up the driveway. :eek:
Thanks for the input!!
 
1st choice AMC401 :D T-18/ D300 4:1

2nd choice Caddy 500 :D TH400/203/205 doubler or Th400/ Klune/D300 Seen a NP435 married up to a caddy 500 with a 4:1 D300 that was a nice combo

3rd choice Chevy big block :D 396, 427, 454, 502 T-18 or SM465/D300 4:1 or TH400/ Klune/ D300

4th choice AMC 360 T-18 D300 4:1

5th choice Chevy small block 350 465/D300 4:1


The big blocks, big stroke big bore motors idle down so much better than a chevy 350. a chevy 350 with TPI idles well at 800 and with good gearsing idles almost as well as a 401 or caddy 500 with so so gearing over the same obsticle


parts are pretty easy these days get a HEI conversion for the AMC from bulltear @$150
Get a one wire GM alternator $100

eliminate all other wires under your hood. now all you have to worry about is a water pump or radiator hose. everything else is cheap and available
 
Last edited:
Depends...

I guess it depends on what you do with your Jeep. If you put a 350 in it you'll always have plenty of access to parts.

I run a 360. :eek:
 
I would have to flip a coin. If I'm being realistic in terms of money, a carbed 401 or an LT1 for EFI.

If I wasn't being realistic, the Edlebrock EFI kit on a 401 :evil:
 
my first choice would be what i'm running right now...

4.2L block, 4.0L head, with Multi-port EFI. tons of torque, and enough horse power for what i do...

my second choice (and would be first choice if i had the money to swap out my engine)

some sort of smaller diesel engine like a CRD out of a late model Liberty or one of the new diesel engines out of the European Jeeps...
 
6.2 0r 6.5 chevy diesel. bolts in with any chevy conversion mounts. tons of torque, lighter than a cummins 4bt and CHEAP (good used engines cost between 200-700 bucks) and i cant complain about 30 mpg in a scrambler either:D
 
If I was to start over, I would drop $800 for a 5.3. Cheap, powerful, and reliable. All qualities I like. But I am happy with my fuel injected 360, and the swap was really easy.
 
Ram Jet 350, comes with multi-port fuel injection- aluminum heads. Lots of comp rock crawlers use this motor, only draw back is $$$$
 
I loves my Furd EFI 5.0, it rocks (literally) and parts are easy to come by too..the stock bellhousing bolts up to a T-18 but I did need an adapter for the T-case, other than that it was just the usual mods...Whatever engine you get make sure it's a modern (newer than 1986) multiport Fuel injection setup, stay away from the throttle-body types of injection, yes it functions but I've known and more than one guy messing around with his throttle body injection on a Chev 350.


MULTIPORT

FUEL INJECTION


nuff said!

:D
 
BIG_Mark said:
MULTIPORT

FUEL INJECTION


nuff said!

:D


I agree 100%..since i have done mine, i have only changed the oil..and put gas in it...and that has been 3 years...and it starts instantly at 0 or 110 degrees....and i can plug in with my laptop and change the shift points on the trans. adjust for tire and ratio combos..etc
 
Just something special about a 401 EFI/DUI, with a Howell injection. (When it's going in a Jeep)!
 
mopedal said:
Just something special about a 401 EFI/DUI, with a Howell injection. (When it's going in a Jeep)!
I'm just 41 cubic inches short of that description.......:rolleyes:
 
Saw this on another site:

Putting a Chevy motor in a Jeep is like taking your sister to prom...it might work but its not going to put out....:evil:

I'm kinda partial to the AMC V8 motors though....I say keep it Jeep:bow:
 
if it is injected...maybe...but i always had trouble keeping distributer gears in them....my brother has a carbed 401 in his cj5...i would not even consider a trade
 
I really like my 304... does everything I ask of it but my dream engine would still be the 401. The only thing I think I need more is Torque. The 401 would provide it. You can find a 304 within a mile of where you live (maybe) the 401 is not so plentiful (which makes me want one all the more). You could do much worse than a 304/360. My pick is still the 401.
 
Back
Top