• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

81 CJ 258 Sniper/Hyperspark install review/questions

TimmyTooTall

Well-known member
Gold Member
Member
SOA Member
City
Joshua
State
Tx
Figured I'd post this in electrical section as most of my questions have to deal with the stock harness.

Looking like I'm going down the EFI route. Want to have better reliability in the mountains this summer. I have read everything I can read about the Sniper/Hyperspark system and seems very straight forward. However most of my confusion is about the removal of unnecessary items that it replaces. Here's my thoughts on my wiring harness and vacuum system and would like a review and any insight please.

1981 main wiring harness. Pre computer non CA jeep. Luckily I don't have to deal with all the nutter stuff. I traced every wire on the firewall block to its source in the engine compartment and labeled below.

1000042181.png
The (code) on each line corresponds to the wiring diagram I'm referencing. Might scan that in and post that later tonight.

I also have the motocraft ignition module below the brake booster and the Idle Speed Control Module or Idle Speed Switch on the passenger fender. It's my impression a lot of these wires will be deemed obsolete.

The IGN module as the following wires
Red&Blue - they both go to the firewall block
Purple/Orange/Black - these go to the distributor
Green - to coil and the ISC
1000041777.jpg

The distributor and the coil will be replaced with the sniper system so essentially this box can be cut out. I need to verify but the Red wire going to block BW will be my 12v switched for the sniper unit. The blue is spliced and also goes to the starter solenoid so that'll spliced wire will stay.

The ISC has these following wires
Orange - switched power from the manifold heater relay
Brown - to wiring block BY (controls idle speed for a/c I believe which I dont have)
White w/ black stripe - TES air cleaner sensor
Red w/ white stripe - Control vacuum solenoid on valve cleaner/wiring block CX
Red w/ black stripe - SolVac on carb
Pink - Control val solenoid
Green - Ign module
Black - air cleaner TES sensor/ground on engine block

1000042132.jpg

All of these seem obsolete as well. These are all essentially a function of upping or controlling the idle. With removal of the associated vacuum related items I see no reason to keep anything from this box. Thoughts?

Vacuum systems
I plan to keep the OEM air cleaner. The first trap door on the cleaner that closes to keep the fuel vapors when the engines off will be disabled. Not needed with the sniper I've researched. I'd like to retain the TAC system and should be able to.

My confusion is with the TVS the EGR and the CTO systems. What's the consensus on keeping these vs eliminating the EGR? If I remove the EGR there's no reason to retain the TVS (temperature controlled vacuum). I plan to keep the Canister for fuel tank vent.

Fuel
Going with the 15 gallon in tank module. Stock fuel line is 5/16ths. Sniper recommends 3/8s. I've seen reports of people running both. What's the consensus?

Power
Is it necessary to get a higher amp alternator for any of this? I don't have much to power other than my winch. I may wire some lights and a better radio one day.

Starter solenoid
None of the sniper install schematics have the starter solenoid pictured. Wires CX and AX both go to the solenoid. AX is blue and that's the ignition so that'll stay. CX also ran to the coil, ISC and control vacuum solenoid. I don't see any inputs or wires to go to the Sniper CD coil so would all these wires be removed from the solenoid?


I appreciate everyones input. I believe I have a good grasp on it but as it's my first EFI swap I want to cover all my bases before I dive in and I'm all ears
 
Did you read the Sniper 78 page instructions ? Very informative and easy to print out. 96530C19-7D51-4557-BE5D-F42287B6A070.png1BE802D3-997D-4C64-B9E2-1081C6B921F0.png
 
Yep. I've gone through it a few times now. Lots of good info in how to install it. I'm more working around what all can I remove thats OEM thats no longer necessary.
 
On my 84 Postal at least the wiring harness is basically in two sub harnesses - one for the pre carter setup and one for all the gubbins that is needed for the carter. There is little commonality - maybe a short length that has to be sorted. (I think that was the control module area).
Just remove discard all the sub harness for the carter and associated stuff.

For me - keep EGR, CTO and Vac canister - these are pretty much their own system anyway.
I can't imagine a need for a different alternator.
I put 3/8 steel line and didn't like doing it.
I'm running the OEM air cleaner - neutered so it does not pull hot air but am suspicious of the efficiency, mine does not like to go over 60 but it has 4.1 gears.
 
I put the sniper on my Overlander and documented everything in this thread:


I did not replace the distributor, I don’t think there is enough performance gain by replacing it with the msg or Holley versions.

I tried to use as much stock systems as possible during the installation. I also installed it in such a way to make it very easy to convert back to carb if I want.
 
Yep. I've gone through it a few times now. Lots of good info in how to install it. I'm more working around what all can I remove thats OEM thats no longer necessary.
Install, make it work by following their instructions, drive it and convince yourself that it's right.

Then come back and look at what you can remove. Highly recommend against trying to thin things until after you've confirmed everything is working. After the install, most of it will become obvious.
 
I don’t think there is enough performance gain by replacing it with the msg or Holley versions.
Having the ECU optimizing timing to match the current load/RPM/fuel state is everything to me. It ties the entire engine control package together, in my mind.

I actually went down the EFI path on my Cherokee only because the first press release that I got from FAST claimed to have a distributor/ignition control setup for the AMC 360. Only after I got into a deeper discussion with them did it become clear that they meant the MOPAR V8s and not AMC (they actually sent me the wrong kit initially because the marketing guy I was working with didn't understand the difference despite me being very clear about what it was going on.)
 
Does the Sniper/Hyperspark system adjust timing for elevation? That is pretty important in the upper elevations of the Rockies.

The only thing I didn't see specifically listed that I needed for my TBI swap was crank signal. The sniper may be different than a GM TBI but I needed a crank signal to let the computer know I was trying to start the engine. Other than that there isn't much to hook up. 12V constant, 12V run, 12V crank and some grounds.

As @bigwalton stated above, get it hooked up and working properly before removing or thinning wires. I wanted to thin down my harness but at the end of the day decided it wasn't worth the time and effort when it was already working.
 
Having the ECU optimizing timing to match the current load/RPM/fuel state is everything to me. It ties the entire engine control package together, in my mind.

I actually went down the EFI path on my Cherokee only because the first press release that I got from FAST claimed to have a distributor/ignition control setup for the AMC 360. Only after I got into a deeper discussion with them did it become clear that they meant the MOPAR V8s and not AMC (they actually sent me the wrong kit initially because the marketing guy I was working with didn't understand the difference despite me being very clear about what it was going on.)
I would agree if we were talking about a more powerful engine. Until the head is replaced with a better flowing one, trying to get much more performance from the 4.2 is rather futile (IMHO). Having a well tuned up stock system will deliver the ignition this engine needs.

All that said, I totally agree with installing and seeing if you like it, before removing unused wiring.

If I was to start over again, I probably would have stayed carbureted. (I have one in a box that I keep in the Jeep just in case I have efi issues, which I have several times. One issue was a blown fuse feeding the run signal to the sniper that killed the whole thing. Another issue is it randomly refuses to start, another forum member thinks it might be the display overheating since I have it mounted to the windshield.)
 
I put the sniper on my Overlander and documented everything in this thread:


I did not replace the distributor, I don’t think there is enough performance gain by replacing it with the msg or Holley versions.

I tried to use as much stock systems as possible during the installation. I also installed it in such a way to make it very easy to convert back to carb if I want.
Thanks ag4! I looked at your thread extensively. Your fuel setup is intense lol. I'm trying to de clutter my engine bay :ROFLMAO:. Thanks for the info
 
Install, make it work by following their instructions, drive it and convince yourself that it's right.

Then come back and look at what you can remove. Highly recommend against trying to thin things until after you've confirmed everything is working. After the install, most of it will become obvious.
100% absolutely. Plan is to remove and tie up unnecessary things to get it going then do the final clean up after install. I'm still in the whole overview/understanding stage of what I'll be getting myself into. Thanks bigwalton!
 
During my deep dive into the wiring I discovered the intake manifold heater wiring is shot. Can't find much online for a replacement. Hoping I can take apart the heater and just run a new wire.
1000042161.jpg
 
If I was to start over again, I probably would have stayed carbureted. (I have one in a box that I keep in the Jeep just in case I have efi issues, which I have several times. One issue was a blown fuse feeding the run signal to the sniper that killed the whole thing. Another issue is it randomly refuses to start, another forum member thinks it might be the display overheating since I have it mounted to the windshield.)
If I was just going to drive around here or Texas for that matter, ( flat lands and low altitudes ) I probably would have gone carb also. But a couple of times in mountains off camber convinced me to try something different. Also Utah and Colorado are calling out to me.
 
During my deep dive into the wiring I discovered the intake manifold heater wiring is shot. Can't find much online for a replacement. Hoping I can take apart the heater and just run a new wire.
View attachment 112418

I suggest finding a good replacement. It can be rebuilt, but I have not found good rivets to reassemble it.
 
Thanks ag4! I looked at your thread extensively. Your fuel setup is intense lol. I'm trying to de clutter my engine bay :ROFLMAO:. Thanks for the info
I have an in tank replacement (Holley brand) for the 15 gallon tank that I am retro-fitting for the 20 gallon tank. It involves extending the pump lower and using a new float arm to achieve full tank depth measurement. I will probably abandon the surge tank once that project is complete. But that project is not urgent since the current fuel system seems to be working well.
 
Does the Sniper/Hyperspark system adjust timing for elevation? That is pretty important in the upper elevations of the Rockies.

The only thing I didn't see specifically listed that I needed for my TBI swap was crank signal. The sniper may be different than a GM TBI but I needed a crank signal to let the computer know I was trying to start the engine. Other than that there isn't much to hook up. 12V constant, 12V run, 12V crank and some grounds.

As @bigwalton stated above, get it hooked up and working properly before removing or thinning wires. I wanted to thin down my harness but at the end of the day decided it wasn't worth the time and effort when it was already working.
Not sure about the timing at altitude but the crank signal if you do the whole swap with their hyper spark distributor utilizes a hall effect sensor.
 

I suggest finding a good replacement. It can be rebuilt, but I have not found good rivets to reassemble it.
Saw that on your thread. Do you have a part number where you found that VW one?
 
I will need to look back thru my notes, it might have been an eBay special. In the end, I recall just using a heater from another intake I had laying around.
 
With the EFI, I wouldn't bother with the manifold heater. That's to help evaporate gas on cold start and you'll be dealing with atomized fuel spray from the injectors already and it primes the intake with a start-up cycle anyway.
 
Back
Top