• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

81 CJ 258 Sniper/Hyperspark install review/questions

Does the Sniper/Hyperspark system adjust timing for elevation? That is pretty important in the upper elevations of the Rockies.
Somewhat ignorant question, having never dealt with altitude compensation.

How would it not be automatically adjusting for this by simply doing what it takes to optimize the A/F ratio?

Isn't this what any modern EFI vehicle is doing at altitude? The idea that the EFI would always ensure that the A/F ratio is as good as possible is precisely why I wanted to run it.
 
I would agree with that if it was MPI EFI. But if it is TBI EFI it’s better than a carb,but still going down the intake where MPI is going into each cylinder. :shrug:
 
I would agree with that if it was MPI EFI. But if it is TBI EFI it’s better than a carb,but still going down the intake where MPI is going into each cylinder. :shrug:
True, but very, very different though IMO from dripping liquid fuel into a puddle below the carb.

Basically the difference between MPI and TBI is pretty small and a VERY long way from a carb where the manifold heater won't come into play.
 
Except carbs don’t drip fuel down the intake, they have fuel sucked out of the jets through the Venturi effect. This fuel is atomized through this process. The accelerator pump does spray fuel into the intake mechanically, so that could pool in the intake. But so can fuel primed by the injectors before air starts flowing.

I would keep the heater if planning to drive it in 40 degree or below weather. Otherwise it really is all academic.

BTW, Belizeit has a 4 cyl intake that looks to have a good heater on it. I’ll bet it is the same as the 6 cyl one.
 
Except carbs don’t drip fuel down the intake, they have fuel sucked out of the jets through the Venturi effect. This fuel is atomized through this process. The accelerator pump does spray fuel into the intake mechanically, so that could pool in the intake. But so can fuel primed by the injectors before air starts flowing.

I would keep the heater if planning to drive it in 40 degree or below weather. Otherwise it really is all academic.

BTW, Belizeit has a 4 cyl intake that looks to have a good heater on it. I’ll bet it is the same as the 6 cyl one.
Only talking about startup here, pumping the gas before turning the key is dripping fuel into the intake zero atomization.
 
Somewhat ignorant question, having never dealt with altitude compensation.

How would it not be automatically adjusting for this by simply doing what it takes to optimize the A/F ratio?

Isn't this what any modern EFI vehicle is doing at altitude? The idea that the EFI would always ensure that the A/F ratio is as good as possible is precisely why I wanted to run it.

Yes, the EFI will compensate for elevation to calculate the A/F ratio. Of admittedly lesser impact is that with less atmospheric pressure you can (probably should) run more advance with the timing to help with the decrease in power with elevation gain. The computer will make base adjustments for both timing and fuel based on atmospheric pressure. Only reason I brought that up was that @TimmyTooTall brought up mountains. I know that I wanted as much power as possible when I had my 8 at over 13K elevation in Colorado.
 
Gotcha, didn't think about timing from what would otherwise be required.
 
Yes, the EFI will compensate for elevation to calculate the A/F ratio. Of admittedly lesser impact is that with less atmospheric pressure you can (probably should) run more advance with the timing to help with the decrease in power with elevation gain. The computer will make base adjustments for both timing and fuel based on atmospheric pressure. Only reason I brought that up was that @TimmyTooTall brought up mountains. I know that I wanted as much power as possible when I had my 8 at over 13K elevation in Colorado.
That's exactly it. I don't want to have to finagle with a carb going from 700ft at home to 13,000+ over Imogene this summer. Working on labeling more wires and vacuum lines this afternoon.
 
That's exactly it. I don't want to have to finagle with a carb going from 700ft at home to 13,000+ over Imogene this summer. Working on labeling more wires and vacuum lines this afternoon.
Best thing I did was to add label flags to each wire under the hood. This tremendously helps roadside fixes.

IMG_2357.jpeg IMG_2356.jpeg IMG_2355.jpeg
 
That's exactly it. I don't want to have to finagle with a carb going from 700ft at home to 13,000+ over Imogene this summer. Working on labeling more wires and vacuum lines this afternoon.

You are in for a treat. We went to Ouray in 2022 and spent 4 days exploring the area. What trails are you wanting to run?
5350130A-1191-481E-B181-CAD7CB079BF5.jpeg56A06F7C-6D74-44B8-98FD-208E6DEE2BE4.jpeg
 
You are in for a treat. We went to Ouray in 2022 and spent 4 days exploring the area. What trails are you wanting to run?
View attachment 112432View attachment 112433
Great pics.
All of them... maybe lol. I'm well versed in the area. Proposed to my wife on the summit of Mt Sneffels. Been wheeling those mountains with my family for 20+ years. Will just be the first time taking Pappy. We're shooting for 2 weeks around the 4th of July then maybe hang around for the Colorado Scramble later that month.
 
I installed a Sniper kit/MSD 6 ignition system/distributor on Andy's CJ7 last year:


IIRC:

manifold vacuum to distributor
kept the intake heater
deleted EGR
one "hot" on start run for Sniper
one "hot" on start run for MSD
I did not hook up either air cleaner trap door vacuum things (inner one not needed with TBI, you could use outer for warm up but not needed)
I installed a GM TBI charcoal canister under hood (one line to tank vent, one line to ported vacuum on TB)

Very little Jeep wiring to Holley, just the "hot on start/run" wires. I removed all the original 4 cylinder emission wiring harness/doo-hickeys/vacuum lines.

Hope that helps :thumbsup:
 
I installed a Sniper kit/MSD 6 ignition system/distributor on Andy's CJ7 last year:


IIRC:

manifold vacuum to distributor
kept the intake heater
deleted EGR
one "hot" on start run for Sniper
one "hot" on start run for MSD
I did not hook up either air cleaner trap door vacuum things (inner one not needed with TBI, you could use outer for warm up but not needed)
I installed a GM TBI charcoal canister under hood (one line to tank vent, one line to ported vacuum on TB)

Very little Jeep wiring to Holley, just the "hot on start/run" wires. I removed all the original 4 cylinder emission wiring harness/doo-hickeys/vacuum lines.

Hope that helps :thumbsup:
Thanks spankrjs! I'll look through yours. Yes I agree the wiring on the new sniper is straight forward it's just figuring out what can be eliminated after. Any pre ignition issues deleting the EGR?
 
Traced all the vacuum lines and have some questions.

First off the jeep was a Colorado jeep so it has "hi altitude" vacuum design. From what I can tell the pcv goes straight to the carb and is not tee'd to the "canister purge" line. I only have a vacuum hose hooked up to the signal canister purge.

1000042306.png

1000042267.jpg
Red is to carb bowl which will be eliminated. Green is to fuel tank. Notice only one hose for canister signal purge. From my research it's just ones ported and ones manifold vacuum. So I take it since it's "high altitude" that it only vents the canister while under throttle. Maybe at hi altitude the manifold vacuum robbed too much at idle? So now that I'm back on Texas most of the time run both ported an manifold or am I over thinking this part? 🤣

Anyways trying to figure out what to do with the CTO lines and EGR. Distributor vacuum will be eliminated with the hyper spark.
1000042266.jpg


1000042307.jpg
 
Thanks spankrjs! I'll look through yours. Yes I agree the wiring on the new sniper is straight forward it's just figuring out what can be eliminated after. Any pre ignition issues deleting the EGR?
No pre-ignition issues without the EGR.

To be honest, first 15 years of me driving either a 258 or 304, neither with an operable EGR system, never had any problems :twocents::shrug:
 
I bypassed the manifold heater relay and was able to power the manifold heater successfully. I'm not getting a solid ground from the manifold temperature switch part of the circuit so add that to the list.
Read through your whole build spankrjs and gave me some good confidence on my research and understanding.
 
Texas - Can't imagine you are going to need a manifold heater.
Now Garrett County MD and 15" snow maybe - but there's this thing called salt here...
 
Texas - Can't imagine you are going to need a manifold heater.
Now Garrett County MD and 15" snow maybe - but there's this thing called salt here...
It was single digits last week. Doesn't happen often but when it does why not be prepared. It's already there just need to repair the wiring.
 
It is not totally a function of outside air. The heat of vaporization when the fuel changes from liquid to vapor can drop the fuel air charge temperature significantly. It has been a while since I looked at the activation circuit for the IAH, so I am not sure what temperature triggers the heater. With plans to drive in the Rockies, I would suggest keeping it. For me, I kept it mainly because I wanted the ability to go back to stock in every way if the next owner wants it that way.
 
I might now need to keep this one as a spare. :shrug: I’m headed to the mountains and it’s been darn cold for a few days.
 
Back
Top