• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Bumper End Caps

What about milling them out of aluminum, sand blasting them to get a surface texture, then anodizing them black:thumbsup:

I can tell you I work in the machining sector. The majority of your cost will be in the machining of the injection dies. I am just guessing a little but selling hundreds of these may be the only way to get the cost down to a reasonable amount of money.

I worked in the injection molding industry for 10 years as a mold and die tech, And yes these are some small parts but the mold is going to be very expensive if you water cool it and install air poppets and all that stuff that's required to run hot material.


Having worked in the field I would not be venturing down this road unless there was profit to be made because of the intial cost involved in making a mold.

I would think you would be better off having them made from aluminum and cut with a high speed cnc machine. Then your only cost is going to be getting a plastic end cap measured up to input into a cnc machine then sand blasting. As small as it is it would take no more than 15 mins to cut one.


Just for example we had 5 gal bucket molds that cost 50k and up ucan mold in the threaded studs but that's gona drive up the cost, If you choose not to mold in studs or inserts the you have to have threads cut in bosses to create a place to thread the studs and that's gona drive up cost.

I still think CNC'ing them out of aluminum will be cheaper/stronger, like mentioned above:shrug::twocents:
 
Anything discussed here so far will cost more than some running Scramblers IMHO. Machining out of anything with the shape needed here, the blanks alone are going to put this out of the reach of most folks without cutting anything.

Just for fun, I did a search on aluminum block pricing and found this:
http://www.grainger.com/product/Rect-Tubing-6ALT5?s_pp=false

Just using that number to figure per cubic inch cost and estimating you'd need an 8"x8"x8" block to start each endcap, that's $105 per endcap material cost to start. $210 per set and you haven't done any programming, setup, or cutting at hundreds of dollars an hour or put any finish on them. Any way I see it, there's a LOT of metal removal that will need to happen to make these work.

I know a shop will get better material pricing, but just putting some type of starting point on it. :shrug:

Short of finding someone who can get the machine time cheap and do the CNC programming for free, this is going to be really tough to work.
 
Yep its going to cost alot to make these up but theres always a chance that someone is sitting on a great cost effective idea. Or Just a bump to the front again. Lol

Sent from my SPH-L900
 
G'day Everyone,
I've not been to the forum for quite some time and I'm in the process of "catching up".

I remember that I bought up an enquiry quite some time ago to see if I could get the end caps to fit the rear of the Overlanders.
(They didn't ever have end caps on the front)

The end result was a very big "zero". And I came to the conclusion if you blokes - who have got far more contacts than I - (over there in the good ol' US) can't find them, then I didn't stand much chance of finding them.

The next stage was to see if I could make them out of steel. And, if I was going to do that, why not make the whole bumper as one piece. So, that's the way I've gone.

The pictures of the end cap that, (I think Alex), put on the forum - are nothing like the end caps of the Australian Overlander.
The Australian Overlander end caps look like this:

AmendedIMGP8824.jpg

AmendedIMGP8826.jpg

But when I started to read the thread I got all excited. At last! Someone is going to get them made! Until I saw the photos :confused:
Not fair you blokes. Not fair at all!

I don't know if I should mention this in this thread…but I found another Overlander. It's now home in the shed. It's the twin to yours Eric. A 5 speed.
Oh, and I have another complete top and rear barn door…but I haven't decided what to do with it yet.

I won't stuff up Alex's wonderful thread on the end caps so I'll start another one and post some photos of a recent Rally we went to and I took a Jeep or two along.
 
Last edited:
I know this was 2 years ago, but how'd the end cap manufacturing go? I need a pair.
 
Nothing came out of it because of initial startup costs and I still have access to the same rapid prototype machine so my material costs haven't gone down. On the plus side my buddy recently got a new rapid prototype machine at his work so I can see what it would take for him to make it on his machine. I believe his resolution is also a bit better then mine. CNC is also an option but your probably looking at $300 a piece.
 
I sent my buddy the file to try it on his machine. He said it should fit and will be made from PLA. Good news is it is also a 1/10 of the cost but so is his machine so we will see how the quality comes out. I'm not sure how well PLA will hold up to the elements (weather, UV??). Thing is going to take about 19 hours to print so I should see it tomorrow evening so I will let you know then.
 
Back
Top