- City
- Redmond
- State
- OR
PREFACE_ Originally the pictures in this thread were hosted on Webshots. Well, those bums decided to close the site down, change the name, etc. Lost the majority of the pictures. I Have attempted to rebuild this thread with all the pictures that I can find. So if for some reason some of them seem out of order...now you know why.
Finally! After over a year without driving, working on, or doing anything but harvesting parts....I started the new year out right by starting on the "restification" of my Scrambler. A little background first...it's an 82, and I am the second owner. No rust, and no body damage (when I bought it). I started out by replacing the 4 popper with a 350 SBC. Did alot of other mods, including a 4" lift by Superlift, and incrementally getting up to 36" tires. Then...I twisted the center section out of the rear AMC20, replaced it with a mismatched D44. Next the SBC cracked a head, I still drove it after a lucky dose of block sealer. The final straw was twisting the tailshaft off the T176 trans. It was pushed into the back yard, and served as a parts source for the Jeepster I was working on. Well, the Jeepster is now my daily driver...and the Scrambler is finally getting the attention it deserves. Here's a pic of the Scrambler when bought it...
And here's how it looked midway....
And here's how it looked just after the trans died...
So...here's the plan. I want to build a capable, yet smooth riding trail rig. Plenty of power, fair MPG. No rockcrawler- I want the body to stay cherry. My physical condition (and my doctor) have limited any hardcore off-roading because I have 2 discs in my neck that are crushed, and any severe twisting or bouncing could lead to loss of use of my right arm.
So...here goes!! :jeep:
Finally! After over a year without driving, working on, or doing anything but harvesting parts....I started the new year out right by starting on the "restification" of my Scrambler. A little background first...it's an 82, and I am the second owner. No rust, and no body damage (when I bought it). I started out by replacing the 4 popper with a 350 SBC. Did alot of other mods, including a 4" lift by Superlift, and incrementally getting up to 36" tires. Then...I twisted the center section out of the rear AMC20, replaced it with a mismatched D44. Next the SBC cracked a head, I still drove it after a lucky dose of block sealer. The final straw was twisting the tailshaft off the T176 trans. It was pushed into the back yard, and served as a parts source for the Jeepster I was working on. Well, the Jeepster is now my daily driver...and the Scrambler is finally getting the attention it deserves. Here's a pic of the Scrambler when bought it...
And here's how it looked midway....
And here's how it looked just after the trans died...
So...here's the plan. I want to build a capable, yet smooth riding trail rig. Plenty of power, fair MPG. No rockcrawler- I want the body to stay cherry. My physical condition (and my doctor) have limited any hardcore off-roading because I have 2 discs in my neck that are crushed, and any severe twisting or bouncing could lead to loss of use of my right arm.
So...here goes!! :jeep:
Last edited:

)
(no other choice... hmmm, need to try to get that thing to someone who can use it).

, like Eric said, you'll have to notch that crossmember. I didn't know to do that, it wasn't in the Ruff Stuff instructions. I cut it with the box in place...not recomended. I cut into one of my p/s lines and my notching job looked really nasty, but it worked...eventually. Cut it when the box is out or lowered out of the way.
It sure explains why the front shackles were splayed- I see alot of Jeeps that way. No biggie- I'll build new rear hangers, spaced out a bit. I'll also be building a tubular crossmember, with inner flanges- spread the frame back to stock width.