• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Shaking Like a Leaf at 50mph+

Crazyredneck87

Basic User
City
Pomeroy
State
WA
Ok, Ever since we did the Spring over Axle Conversion. Anytime I get up to 50 mph or higher the entire Jeep feels like its shaking apart. Though it feels like the front end is sliding side to side. I have replaced all the wheel bearings,All the U Bolts are extremely tight (reefed on em with a cheater bar to eliminate them).Front Drive shaft is off as well. I just took it in for an Aligment and still is doing it. I aint sure what is going on. Though I did notice the front driver side is sitting a bit lower got to looking at it and the spring perch is sitting higher on the passenger side not sure if this would play into the issues. Tires are good to go as well had them checked out as well they best be they are brand new tires.

So I am coming to yall for some insight on this. Its driving me up the wall. My neighbor whom also is a jeeper couldnt figure it out either. So I am hoping someone here has had the same problem.

Specs on Tires are Mickey Thompson Baja MTZ 35 12.15 15s.

Dana 30 Front.
 
I agree on the caster. The link from Rustycrawler will be time very well spent studying it. Very well done. I'm sure you've checked your tie rod ends, but also check the steering box mount. I'v run into several broken box mounts in the past couple of years. Our babies are 30 + years old now and starting to show some of their fatigue. :wave:
 
X3 Caster...if you make a turn and wheel does not return to center on its own...then you do not have enough caster...it is common that people tilt the pinion up when they weld on the spring pads...this is exactly the wrong thing to do!!!...caster should be between 4 and 8 degrees off vertical angling to the rear of the jeep.
 
Thanks guys. I have alot to think about it now. I will def check out the casters. Though at this point I am thinking this is a sign to just drop the money and upgrade from the dana 30 and amc 20 and do my RokJok 60s I been drooling over at Currie Enterprises. Though not sure I can justify dropping 8grand into them though 4.10 gears ARB AIr Lockers Rear Disc Brakes and all that good stuff but I ain tsure if I want those first or do the bodywork/paint lol...
 
I had a serious caster issue because the PO had installed some extra long front shackles. I never could understand why it wandered all over the road. When I finally sat down and did my homework and figured it out, I removed the extended shackles and WOW! what a difference. It drives straight and true. I don't look like a drunk anymore. ahhaha I didn't know that a caster issue could cause a vibration problem though.
 
I have made the decision to take it into the local 4x4 shop and see whats going on and what he has to say we just cant find the issue...Its driving me up the wall. Worse case I drop the money into the new axles sooner then I was anticipating but hey might be better to put the money and time into putting the new axles on then repairing and updating the current ones.
 
New axles are not guaranteed to fix this and could be even worse. Find the issue and solve it with what you have. Did you measure the caster?


 
So after extensive going over with the local 4x4 shop we checked the caster,we checked the inner axles the wheel bearings the gears it self everything. Low and Behold when I TOOK the tires into the damn shop they didnt even put them on the balancer because they were to "HEAVY" they put in a liquid balancer. Well they didnt tell me that. So I have taken em into another tire shop they checked the balance and came to find out they were not even close to being balanced with the liquid balancer so it ended up costing me another 120 bucks for mounts dismounts and balances. But good news is why it was apart I went ahead an added a High Steer Kit still looking at new axles but at least now I am able to get the paint and body work done first!
 
After having em checked again after we got em on the rig and found this issue...didnt even have a notion it was them but when I found out the guys were saying they are "Too Heavy" yet when I called to complain to them that they failed to do the job correctly the guy at the desk said oh we can spin balance 35s makes me wonder if they were being lazy and shortcutting it.
 
Back
Top