• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Small block ford swap

craveman85

CJ-8 Member
City
Dolgeville
State
ny
Originally I had planned on an amc 360 swap for my scrambler. I actually bought one but decided to go a different route due to the cost of having someone rebuild the amc motor, the performance available from the motor and the lack of usable transmissions in my area. I came across a granny gear ford t18 in need of a rebuild for 100$ It came with the bell housing, clutch setup, and a 5.8 flywheel. I'm ordering my adapter to the Dana 300 from novak in a week or 2 so I can get that started. I also purchased 2 351 Windsor engines. One was a $150 eBay buy that was local. It came with an offenhauser 4v double plane intake, edelbrock aluminum valve covers, the duraspark 2 ignition system, the power steering pump, alternator, and associated brackets, and some other needed parts. It was rebuilt 60 over a while ago and has been sitting for a few years. I also bought a 97 351 roller engine with 76000 miles. I'm probably going to tear the accessories and intake off the older engine and put it on the lower millage roller engine. The 97 still shows hone marks on the cylinder walls and I'm unsure of the condition of the older engine internally. Mostly bought it for the intake and accessories.
There's still some stuff I need to get for the swap. Engine mounts are probably going to be more bomb proof mounts. I'd work on fabbing some up but I need a new welder and my body also isn't on the jeep now. Add I said the novak adapter is coming along shortly. The adapter with the t18 and bellhousing is very close to the original length of the sr4 setup. Depending on location of the more mounts I may be able to keep stock length drive shafts. I've read other places that block hugger headers for a bronco fit well with the sbf swap and there's a pair on craigslist for $50 if I can set up a time with the guy. I'm running dual exhaust probably with an x pipe exiting both sides in front of the rear axle. Probably 2.5" but I haven't chosen mufflers yet.
A couple unknown factors are my radiator and the oil pan. The oil pan I've heard that I'll need a rear sump pan but then I've also heard a regular truck pan may work. For that I'll have to wait until my more mounts get here and see if it fits. I've heard that a factory cj7 3 core radiator will suffice and it looks like the water inlet and outlets will work. I thought I had a thread started on that somewhere but couldn't find it for some reason. I'm probably going with an electric fan setup. By my estimates from weights I found online I'll be adding about 250-280 lbs to the front end. Is this enough to make it worth a set of light add a leaf springs?I don't plan on lifting or putting big tires on anytime soon. The jeep will see 97% road use. Probably 20% dirt roads. I don't plan on going bigger than 31" tires, maybe 235/85r16@ ~32" but no bigger. Max lift I'll ever see is probably 2-3"
Anyone else with a sbf swap that has any opinions, trucks, hints, or tips? Pictures of the swap would also be helpful.
 
Yeah iron puke. The sr4 to t18 will add 80 lbs alone. Was there actually a different part number for 4cyl vs 6/8 cylinder springs?
 
IMO running the fuel injected 351 would be worlds better than a carb. You can switch it to Mass Air from a 302 should you desire. Run nice headers into a single 2.5" exhaust. No need or room for an X pipe on a Bronco much less a CJ.
 
On your engine weight, your planned combo won't weigh any more than an AMC V-8 and trans combo.
 
Definitely not going efi. I feel all that crap looks ugly under the hood of a vehicle where it doesn't belong. That and I plan on upgrading things in stages as I get bored which with an efi motor would require expensive tuneswhere as a carb is a couple of jets. I drove a carbed chrysler 5th ave for years that I modified often. Never had reliability issues or worried about starting in cold weather. Only time the car left me stranded was when the auto trans stuck in high gear and burned up. I think I may see if advance adapters long tube headers will work and run side pipes.
 
The scrambler won't be a year round daily driver. It's only going to be a summer cruiser and doesn't need to pass emissions testing because of its age.
 
I've decided I'm going to make my own engine mounts instead of using more ones. Should save me 225$ and I want to use advance adapters long tube headers what go outside the frame rails. The more ones move the engine off center so it could cause clearance issues with headers.
 
I just did this swap. But I used the Ford EFI and an nv3550 I rebuilt. Ask away, I can take pictures of whatever you want.

My opinion on a few things you mentioned:
1. engine mounts.
I made a set first, placing engine in "stock" location so I could keep all stock skid plate, transmission mounts, shifter locations, etc.. unchanged. Front driveshaft clearance was a problem, and would be a bigger problem for you with less lift than I have. Also, you will have clearance issue with driver side cylinder head hitting firewall. It will hit just at the floor pan to firewall seam above and right of gas pedal. So it can be clearanced, but will be a lot of work and leave you with a "custom" indent that may or may not be an issue depending on what future plans hold. I went back and bought a set of MORE mounts and they are as good as they look. Modifying mounts and shifters was not that big a deal.
2. headers.
I wanted to use the stock mechanical clutch linkage (and thought I wanted a single exhaust). So block huggers seemed like a good idea. I borrowed a set to see how they would fit and they interfered with the passenger MORE motor mount. They were Hooker's, don't know which you are looking at.
Then, because I have lots of leftover parts, I tried some f150 shorty headers. Bam. perfect fit. So I would guess that f150 long tubes may work, but not 100% sure. The exit exhaust point is about an inch higher on the 5.8 than it is on 5.0, but based on how mine fit I think they would work fine.
I looked at fenderwell headers too (outside frame). You will have to major league cut up your inner fenders. No more stock radiator overflow bottle location, may keep washer bottle location, but no stock ignition box location, vapor canister, fender braces, etc.. Basically you will not be able to mount anything on fenders other than very top and may lose some fender bracing. And, depending on your wheel offset and tire width you may have rub issues at full turn (not sure on this, I was measuring other installations for info and one hit and one didn't)
3. Your block and fuel delivery
I would plan to use the 97 roller block. I would take off valve covers and intake and if it looks clean in the valley and the oil returns, put it back together with offy manifold and carb, and run it. Those high nickel roller blocks are good for a couple hundred k no problem. That block will have better heads than anything older and is roller cam ready for future upgrades.
If you are not planning to wheel it, and you know how to set up and tune a carb and vacuum advance ignition, then that is a good option that will be cheaper. But no matter how well you tune/tweak/customize it.... it will never be as good as EFI.
Having said that, I can tell you that the OBD1 (EECIV) Ford computers are getting hard to find and expensive. So if you wanted EFI later you could always grab a Holley system off craigslist or ebay and add later.

Couple other things - make sure you get the right starter and bellhousing to match your flywheel you decide to use. They do not all interchange (not all 5.8 motors had 164 tooth flywheel and the 157 stuff is different). Make sure the balancer you decide to use matches your flywheel. Shouldn't be an issue with 5.8, but double check.
 
Oh yea...
Oil pan.
You can use the truck pan, it will fit no problem. They usually have large rear sump with small front sump (2 drain plugs). Unless you have something I never saw before, which is possible....

Radiator
I am using a stock 3 core with Ford Contour fans and a 195 thermostat. The only time the fans come on is if I let it sit still and idle for some time. Running down the road the engine is on the thermostat, no fans needed. So plenty of radiator.
The Contour fan set is plentiful in junkyards, holds 2-12 ish inch fans that can be set up to run on low and/or high, They are thin for plenty of front engine accessory clearance, and they fit the CJ radiator like they were made for it with no modification.
 
Since I cant figure out how to edit...

If you don't plan to wheel this rig hard, why use a t-18? Have you driven one before? They are a for real truck transmission and act accordingly in terms of shift length, speed and smoothness. The SR4 will not last behind a 5.8, but the jeep t-150 would and is basically a better shifting t-18 without the 6 to whatever it is granny gear you will never use on the street. A jeep t176 would hold up too, and neither of those would require an adaptor to the d300.
 
I've driven a t18, I may use it for launching my boat from time to time so a low gear would be nice then. Other transmissions are very hard to find around here. I was originally looking for a t176 but have given up on that end. I don't want to go with the t150 because novak states it's not compatible with the Dana 300 which I already have the 4:1 low range kit and a twin stick kit for. I don't wheel currently but may eventually. I live in the Adirondacks in ny and there's only wheeling here on private land which I know of nobody who has anything I can wheel on. However if I move somewhere that I can wheel and own whatever guns I want then I won't need to go through the trans issue again. And pretty much every trans I would get I'd still end up with the 1:1 final gear. Basically it's a good beefy 3 speed with a granny gear.
I have the bell for the 164 tooth housing, bought a brand new starter, stripped all the parts I needed from the 85 351. I found the offy intake is a dual port not the dual plane. It's got the primaries and secondaries split into two completely separate planes. All the runners are split into 2 ports. I've got a 480 cfm autolite carb that's going on it.
 
Did the scrambler ever come with a hydraulic clutch? Coulda swore mine had a master cylinder when I took it apart. Where was the driveshaft a clearance issue? I think the novak adapter to the t18 can have the case angle adjusted. Maybe enough to clear any issues? Maybe when I get to the exhaust stage I'll see if I can borrow some headers from people to check fitment Maybe I can run block huggers and side pipes
 
The four cylinder Scramblers used a hydralic clutch.

Did the scrambler ever come with a hydraulic clutch? Coulda swore mine had a master cylinder when I took it apart. Where was the driveshaft a clearance issue? I think the novak adapter to the t18 can have the case angle adjusted. Maybe enough to clear any issues? Maybe when I get to the exhaust stage I'll see if I can borrow some headers from people to check fitment Maybe I can run block huggers and side pipes
 
Ok I thought I had one. That should be relatively easy to hook up then. I tried editing to say shorty headers instead of block huggers. I'll probably go with more mounts since it looks like the aa long tubes are out.
 
I think some did come hydraulic, but mine wasn't. Not sure what the combo or year would have needed to be; mine stock was an 84 Laredo 4.2 with t5/Dana300.

The driveshaft was a problem at the transmission flange and the bellhousing. I didn't fully compress the springs to see if it would hit with stock bump stops, but according to tape measure it would have. And I used a clocking ring too and it didn't help much up or down.
But you may have different results. Some folks told me I woudn't be able to use the stock skid plate, but it worked perfect after I drilled a new set of mount holes for tranny.

Any of the exhaust ideas you have will work. Just depends on trade-offs.
If you know you want to come out the sides, fenderwells are not a bad idea. You will not have to worry about the pipe that runs under the frame later if you decide to wheel it.
I had my exhausts out the sides on a different rig, so I knew I wanted it at back corners like factory on this one. So I needed to stay inside frame rails for the length run.
I was going to use block huggers when I planned a single outlet so I could cross passenger pipe to driver side under oil pan in front of sump. When block hugger hit motor mount, I looked at other options beyond cut/weld on the huggers. Turned out the f150 shorties allowed me to run dual 2.5 inch, with an h-crossover behind the transfer case, with less effort than the cut/weld on the huggers would have been to get a single worked out.
 
You probably thought about them.. what did you some up with on 5 spd trannys?

You really cant beat $100 for the t-18, but no overdrive.

I have about $300 into my nv3550 including rebuild. And I could have re-drilled the flange to mount the d300 and not needed an adaptor of any kind for the transfer case. (but would have on bellhousing) An AX-15 would be same deal.
 
With a 5 speed I'd need an adapter for the bellhousing. I will still keep an eye out for a 176. I won't really need overdrive. I drove my ranger for a week not using 5th gear to test this and it seemed fine. I'm not going to be hitting the interstate with it so I'm not worried about high rpms. Mostly 35-50
 
Back
Top