• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

The little flatty--for a lil fella

Rockwell

Ok--after a little bit of a burnout I finally got out from under it(still a little there so I am ramping back up to my origional pace).
So here is where I am starting. I went and drug the tranny and t-case dale had dropped off. Both these damn things are HEAVY and I prefer to work smarter than harder whenever I can so I grabbed the cherry picker. So lets start with the t-case. Its a rockwell t-case and I am not real familure with them but look pretty beef and an interesting case. The case apears to be close to a 300 in the length of the cast case--but the neat aspect of the case is the rear output drops in the bottom of the case. So me being me I HATE working with grubby parts and spent a couple hours cleaning the 3" deep(lol) of crap off it.
gmb194.jpg

gmb195.jpg

And all clean
gmb196.jpg

gmb197.jpg

I had one of the Rockwell transfers for several years. I believe it must have been designed for the short wheelbase CJs. Ya gotta love that dropped rear output!

As always, great workmanship. :bow:


:wave:
 
I had one of the Rockwell transfers for several years. I believe it must have been designed for the short wheelbase CJs. Ya gotta love that dropped rear output!

As always, great workmanship. :bow:


:wave:

Thank you sir..
 
Ok figured time to update this. Still chomping thru it..

So I ripped the silly stock steering parts off the rig :redneck:

forum


I got the knuckles drilled out and rod ends thrown on the new tie rod. At first I just threw the tie rod on to get some ideas bouncing in my head.

gmb215.jpg


At this point I noticed an issue I need to resolve. I went and checked the caster and its sitting at like 11 degrees---oh my. So I have some shims coming to get that somewhat corrected. Now granted its not extreemly critical with how this rig will be used compared to a rig that will see the street allot. But it needs to be corrected mainly because I need the room between the springs and steering arms for the tie rod to sit on top of the steering arms. But making some progress :awesomework: and once the tie rod is able to be bolted down then I can swing into ram mode.
 
So I made better prgress tonight than I was expecting

So since the arms(center of BJ to tie rod mount) as pretty short and the tie rod is nice and beefy(refer to my overkill your steering always thought process) I had a clearance issue with the diff cover.

Well it took a little bit of work but I got what I wanted..



gmb216.jpg


You look at that and OMG its close to the ring gear. Well the cover is 1/8" thick and there is at least 1/8" clearance to the ring gear. Its just "perfect".


gmb217.jpg




Clearance to the tie rod. There is aprox 1/8" there--again perfect


gmb218.jpg


With the clearance and the size of the ram--this is where its going to sit.


gmb219.jpg


I was actually able to start the mount on the housing tonight
 
The ram mount was certainly tricky due to the narrowness of the spring width and the ram diameter--but I was able to sneak it in there on top of the tie rod like I wanted. Here it is all tached up.

gmb220.jpg


gmb221.jpg


gmb222.jpg


gmb223.jpg


gmb224.jpg


I ran the mount as far against the spring perch as I could. I ended up notching the mount for the U-bolt to slide up though.
 
Got it all welded up tonight and threw some paint on it.

gmb225.jpg


gmb226.jpg


So in the morning I will get the toe set and finish up the tie rod mount side of it.
 
Ok so I got the toe set and my tie rod length was spot on the $$.

So I went and checked the ram length/travel and damn if I wasn't 3/16" off on my measurement(ram travels 3/16" too far). Now this is a piece of cake to fix but the hard part is popping this type of ram open.

So what I had to do was build a tool to get the cap off it (spanner type tool).

gmb227.jpg


gmb228.jpg


I ended up breaking a few bolts on the tool before the dang thing finally let loose.

gmb229.jpg


So all I have to do is make a 3/16" thick washer and we are back in bussiness
 
I got the spacer cut/made and re-assembled the ram.

gmb230.jpg


The throw is perfect. I just gotta finish up the mount for the tie rod and moving right along...
 
I knew I was forgetting something--crazy week (up to 43 hours at work so far this week).

In any case the front is back under the rig with the steering setup. I have new bolts and I have to pull the tie rod off and paint it.

gmb231.jpg


Both spring plates are cleaned/painted and U-bolts trimmed. I had to modify the drivers one to fit due to the location of the ram mount.

gmb232.jpg


gmb233.jpg


Shouldn't have to worry about the ram any.

gmb234.jpg


gmb235.jpg
 
Finally got the AA bellhousing


gmb236.jpg


Man now I am excited and I am back into my game finally--the funk is gone. So I have to do a little reading to do over the next few days (hoping to get the rig moved back over next weds/thurs) to get the clutch stuff figured out (slave/master) and will be full awn rolling again...
 
Ok got the shop scrubbed down/cleaned..

Started by looking over the new AA bellhousing and making sure its right---sure looks like it. Ya wanna know how to lighten up an SM465---replace the cast/steel bellhousing.

gmb237.jpg


Went and polished the tranny/bellhousing surface and made sure the pilot bearing that came with it was right--yuppers.

gmb238.jpg


So I looked over the surface and found the tranny top overlaps the bellhousing surface a tad. With the stock bellhousing that was not an issue as the bellhousing stopped before it and the new AA one does not.

gmb239.jpg


Thats not a big issue but I will have to pop the top off the tranny and grind that area down and reinstall it. So that will be my morning prodject before we head to the sultan shindig.

I also have to research farther on the clutch part of it but I can still assemble the trans to the motor and continue moving forward hopefully with very little stops.

But for the clutch slave it suggests using a toy FJ slave. I am not sure if the bellhousing is made(mounting wise) for it but the clutch fork is very simular the one in my rig.
 
Looking great, Crash. Good to see you making progress again.
 
Crash - I hope you don't trip over all the compliments I'm always throwing at you, but....YOU ARE THE MAN! I am going to be making my first attempt at a hydraulic assist ram install later this year, and your post is definitely giving me some direction. Thanks again for taking the time to post up, and please let us know in advance if you ever plan to come to the east coast so we can show you a little southern hospitality!


-Mike
 
Thanks guys Wildturkey glad I could be sort of inspiration....

Ok back to having crap fall on my head :rotfl: (will have more updates tonight)
 
Time to get this up to date...... I have been working hard on it so I can get ready for my dads car.

Ok got the top of the tranny popped off and did a quick inspection. There are a few small rust spots but nothing I would even worry about.

gmb240.jpg


The new AA bellhousing comes configured with all 4 mounting holes threaded. This sm465 the lower 2 holes on the tranny bolt to the bellhousing and the 2 upper bolt to the tranny. So to fix this I simply drilled out the threads on the upper holes.

gmb241.jpg


Walla bolted to the tranny. I have to get new bolts for the lower holes since the bellhousing is thicker than the stocker.

gmb242.jpg


Got the cover ground down and fitted and reinstalled.

gmb243.jpg
 
Got the tranny carted back under the rig and got the motor dropped down into place and then bolted the tranny up to the motor.(minus the flywheel/clutch/pilot bearing for ease)

gmb244.jpg


Now the fun begins. So I did some moving/measureing and have come to the conclusing the motor needs to go forward 1", down 1/2" and to the passenger side 1/2". These are just rough figures as I have to do some work to get the tranny/t-case to fit up into the rig a little better.

So I have to trim some off around the top of the tranny and rework some sheetmetal at the top of the t-case.

gmb245.jpg


So in the morning I will pull the tranny back out and do some sheet metal work
 
So I got the floor modified to get the t-case where I want it. So I pulled the motor back out and removed the mounts off the frame.

gmb246.jpg




And got the motor tossed back in/bolted to the trans and getting the motor into place to build the new mounts on the frame.

gmb247.jpg
 
Here are the old mounts that I whacked off the frame.

gmb248.jpg


Here is the start of the new mounts I am making. Since the motor is a little lower and a tad more forward there is no longer a straight shot from the bottom of the mount to the frame rail. Thats the reason for the bend in the bottom portion of the new mount footing.

gmb249.jpg


Got them trimmed and tacked into place. Next was to do the side supports and got them tacked into place. So now the motor is ready to come back out so I can fully weld them up and progress forward.

gmb250.jpg


So doing some reading and looks like we will need a conversion clutch and of course the only thing AA shows is part numbers for centerforce stuff.

Also trying to figure out what clutch master/slave to run. But as of right now its looking like FJ stuff will be the key...

In any case still moving forward...
 
So the new mounts are welded in and painted

gmb251.jpg


gmb252.jpg


Got the motor back in and bolted to the tranny and checked fitment. I really like how the motor sits now..

gmb253.jpg


Got the back half supported and in place and now time to figure out a cross member--its going to be tight and tricky..

gmb254.jpg


I also started eyeballing placement for the cross supports for the fenders and I have a few ideas but I will wait till the crossmember is done.
 
Back
Top