• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Time to finish the Scrambler.... oh... and a new JK Unlimited on order

Joe West

Arizona Virtual Jeep Club
Lifetime Member
City
Laurinburg
State
NC
Hi Gang,

Since my move to North Carolina in July, I have been using the Scrambler every day. It drives me to work at the University of North Carolina, hauls hay for our horses, pulls a mower to mow the pasture, and it has even pulled down a shed (with the help of a Warn 8274 winch). In short, it has been quite the working Jeep.... it is however, telling me it is time to rebuild the engine. I will be taking it offline to rebuild the engine and get it painted...

as

soon

as

Jeep

delivers

the

2015 JK Unlimited Hard Rock I ordered a week or so ago.

I honestly never thought I would be buying another new Jeep. New vehicles tend to be poor investments. This being said, I knew what I wanted and after looking around, I couldn't find it new on a lot or used anywhere in NC or SC. The primary specs were that it needed to be a manual transmission orange colored rubicon. Pickins were slim so I broke down and ordered directly from Jeep. The new ordering process at Jeep is pretty neat. You place the order and receive a Vehicle Order Number (VON) within a day from the dealer who is ordering it for you. In a day or so, Jeep assigns a VIN. Armed with the VIN and/or VON, you can call 1-877-IAMJEEP and receive updates on the status of your build. My JK Unlimited Hard Rock (JKUHR) has all the parts assembled and in stock for the build and is scheduled for build (code D1). Once Jeep starts putting it together, it takes only a day or two to build (in many, but not all cases).

With any luck, I will have the JKUHR in late December or early January, and will start taking the Scrambler apart. I have a great garage here in NC (standalone building with 20' ceilings, three bays and a workshop... just at 1,000 sq. ft.) and am really looking forward to pulling the engine and rebuilding it. While I am rebuilding the engine, I will take all the trim, fenders, grille, etc. and flatbed it to a shop to have the bodywork and paint done. I have no idea how to find a good shop. I had a good one in Arizona, but here in the sticks in NC, I am a bit worried about finding a good paint and body shop.

Anyway... just a quick update. Once the actual work on the Scrambler begins, I will update my original build thread with the details.

Joe
 
Wow. Sounds like exciting times are coming. Glad the Scram has been a workhorse for you.
 
Hey Joe,

Where in North Carolina are you? I am in Burlington, if you are close enough maybe we could meet up.

Greg
 
It really is a rubicon with some added options. 4:1 transfer case, Dana 44s front and rear, electric sway bar disconnect, rocker protection, 4.10:1 gears, etc. I ordered it in sunset orange with painted top and fenders, dual tops, full and half doors, temperature controlled A/C, and leather seats. The last new jeep I owned was a 1998 TJ. I am looking forward to a vehicle that is a bit more comfortable than my scrambler, which has been my daily driver for a little over six years.

Speaking of the Scrambler, I was using it yesterday to drive around the property and pick up firewood. I can see why Ronald Reagan had one for his ranch; the Scrambler is a great little work horse.

Joe

Sounds awesome Joe! What are the specs of a JK Hard Rock?
 
We are in Laurinburg. According to Google Maps, we are 103 miles away. I will let you know the next trip I take to Raleigh, perhaps we can meet up.

Joe


Hey Joe,

Where in North Carolina are you? I am in Burlington, if you are close enough maybe we could meet up.

Greg
 
You going to keep the motor stock or build a stroker?
 
Good question. I will most likely leave it bone stock.... except that I will use higher quality parts than the factory did (forged pistons, etc.). It will be nice to take my time rebuilding the Scrambler engine... before I ordered the JK, I was planning on trying to do the rebuild over the month I get off for Christmas break (being a university professor has some benefits to offset the... ahem... low pay :D ).

Joe

You going to keep the motor stock or build a stroker?
 
So, did the air cooled car make the trip too? You have to plan on coming to the Nationals for vairs in Knoxville next June!
 
Indeed it did. I would never leave it behind!

I will make the nationals next year. My brother lives in a small town name Petros which is very near Knoxville. I'm glad you reminded me when the nationals are; I have never been to a single CORSA event in the 25 or so years I have owned the Corvair.

So, did the air cooled car make the trip too? You have to plan on coming to the Nationals for vairs in Knoxville next June!
 
IF I am not mistaken, the date is June 23 thru the 27th. I have never been to a national event either. You also need to plan on going the Springfest in Helen in April... And then to the Choo Choo event in August!
 
I live ten miles from Helen. I'd like to meet up with some of you guys if you do the Helen event.

You do realize we are talking Corvairs and not Scramblers? ;) Helen is like April 25-26, IIRC.
 
Lol. I wouldn't blame anyone for being confused. Corvairs are somewhat off topic in a scrambler forum. :D

You do realize we are talking Corvairs and not Scramblers? ;) Helen is like April 25-26, IIRC.
 
Working Scrambler:
 

Attachments

  • IMG_0199.jpg
    IMG_0199.jpg
    302.8 KB · Views: 40
Back
Top