• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

What did you do with your Scrambler today?

Status
Not open for further replies.
This was earlier this week, but I had to get the pictures from my neighbor. His dad and a friend dropped off an 800+ lb maple tree trunk at his house a couple weeks back. My neighbor only has a pair of Subarus, so he needed some help getting it to a sawmill near here.

Plan was to use the big trailer behind the JK (only real tow hitch setup other than the Bus) and hook up the Postal's winch to the front of the trailer with a snatch block to pull the log up onto the deck. Ended up with the log wanting to drag the Scrambler on his driveway once it got onto the ramps, so it was 4lo time and that got the job done.

We were up against a time deadline, so I was busy and his wife had to take the pictures.

The Postal night winching, actually, this was after having to drag the monster in 4lo. Note the blanket on the winch line, safety first.
259827_4879198979758_2123165624_n.jpg

The log on the back end of the trailer. Glad we didn't have to go far, pulled like poo loaded like this.
542795_4878817610224_818909269_n.jpg

The biggest PITA of the night was actually after we got it off the trailer at the guy's place with the sawmill. His ATV didn't budge it once it was on the ground. He kept saying "Oh, we'll get it" but the ATV didn't work, the two-wheeled cart on the front end didn't work and we finally had to get it completely on wheels with another two-wheeled cart in the back. Took forever and I couldn't feel my fingers by the time we were done, it took all three of us to make it happen. Sawmill guy kept saying "Damn, that's a heavy log!" Then he had an engine lift with a big pair of pincher things to try to lift it to get the carts out from under it. He had this 5 gal bucket full of sand on the back of it as a counterweight and it still wanted to tip. He said that never happens and ended up having to stand on it to get it to balance just enough to lift each end of the log (just one end at a time, not even the full weight).
601600_4879230540547_268640370_n.jpg

It was close to the limit of this guy's saw. He ended up having to take off a couple of knurls with a chainsaw to get it all. Guy only charged him $20 bucks for all of that! Couldn't believe it. Said he just does it for fun. He was a riot though. Very fun evening.
18125_4879230820554_1250165374_n.jpg

The fun wasn't over, we had to load 800 lb of 2" planks back on the trailer to get home and then off the trailer into his garage. This is less than half of the whole haul. It sure is pretty wood though.
12806_4878817850230_431302616_n.jpg
 
Neat! What is the intended use for the planks? You have to do any winching "insde" the house to get them in place? :wave:
 
He's working on the plan for the planks. He's a pretty damn good woodworker, so I'm betting there will be some cool stuff coming out of his shop...in two or three years after they dry out :eek: Quite wet wood, so he'll have a while to think on it.

He offered me one for the help with the trailer and all, but I told him that'd be like giving a Picasso painting to a blind guy. I don't have skills for anything much more than putting it on sawhorses.
 
A few new HDR pics of the new seat and tower speaker installs finished this week.

Rockford Fosgate speakers mounted on rear cage uprights:
311097_411087458960681_505854025_n.jpg


Wiring run through tub with drain caps and wrap:
481702_411087598960667_490011382_n.jpg


Seats installed with front cage removed:
forum


Look... I have a rough and tumble crawler too! Hardcore flex shot:
405041_411087125627381_1354931793_n.jpg


Happy Thanksgiving everyone.
 
Postal goes off driving insurance to winter storage tomorrow. Just ran to the grocery store and back in it to get stuff for green been casserole. Shut back down in the driveway and there is fuel dumping out from the fuel pump area. Looks like one more thing to look at this weekend before moth balling it. And I cracked my head good on the bumper crawling out from under it.

Awesome.
 
Sorry about that bad news. And your head too. Happy Thanksgiving. 😳
 
11am: got in it... started it, drove it a whole 20 feet.
11:30am: Had to install a new headlight bulb in my VW Rabbit. bulb retainer clip fell off, couldnt see where it had to go because of the angle. Unbolted the drivers side mirror on the Scrambler and used it to reinstall clip on headlight. Reinstalled drivers mirror.
6pm: got back in it, started it up and reversed it 20 feet back into the garage.

(I was working on the Beetle today)
 
Postal goes off driving insurance to winter storage tomorrow. Just ran to the grocery store and back in it to get stuff for green been casserole. Shut back down in the driveway and there is fuel dumping out from the fuel pump area. Looks like one more thing to look at this weekend before moth balling it. And I cracked my head good on the bumper crawling out from under it.

Awesome.

She's telling you you're not driving her enough and protesting being put away. I hope to get a few more rides in before that has to happen for mine.
 
Had some sliders custom made today. Got too late when I got home. Will paint them later this weekend. If anyone in the Metro DC area needs some welding services, the guy who did my sliders is a great guy who does great work at a great price.

AE4C3AEFBEFF42D4ABB9160A9B9FAD8613120000-1.jpg


8098599EFDEB419086DC95EC471CBBBD13120000-1.jpg
 
Last edited:
Nice indeed!

My big Scrambles lately have just been battery maintenance runs. Today was hardtop day so I can be warm again. The rest of the winter will be use when wanted and dealing with the creeping crud that comes from sitting on the seaside all summer :eek: Maybe even a change from Laredo bucket to a 60/40 bench. (Don't hate me for this street worth mod).
 
Started a pretty cool going away gift for one of my Marines.

Drove this 5" MICLIC rocket (mine Clearing Line Charge--used to fire a 1700lb linear explosive charge into a mine field to explosively breach a lane) I had inerted to the auto-hobby shop on base and cut it down.ImageUploadedByTapatalk1353912704.571494.jpg

Once cut...ImageUploadedByTapatalk1353912843.582764.jpg

Picked up a few small parts at the local home depot and a little modification and patience and here is where it site tonight. ImageUploadedByTapatalk1353912932.397932.jpg
ImageUploadedByTapatalk1353912953.534416.jpg



 
ImageUploadedByTapatalk1353912983.286712.jpg
ImageUploadedByTapatalk1353913002.421080.jpg
ImageUploadedByTapatalk1353913015.351195.jpg

Now I have to cut and weld a plate for the base and mount his plaque. Pretty proud of this one. And of course I could never have done it without Ol'Red
ImageUploadedByTapatalk1353913154.445524.jpg


 
Well today alone I have cut all the floor boards out fitted the new floor panels finished up the rocker panel replacement on the drive side and started on the rear panels and corners. Hopefully gonna have it done before Christmas.

Also finalized the paint for my Scrambler today. I have decided to take it from Black and Tan because I just think the other scheme is gonna look killer and going with a Black Body and silver accent with all stainless hardware and carbon fiber autometer gauge kit.
 
Completed my first fabrication job making a bumper to cover up the bare rear crossmember along with getting it painted and bolted on. I have the machine shop manager here at work making me a custom CJ-8 embelem on the CNC's to bolt on as well.

forum

forum

forum
 
Status
Not open for further replies.
Back
Top