- City
- Biloxi
- State
- MS
New oil fill cap and front PCV valve components installed:

Finally installed/hooked up the PCV fresh air hose components on the rear of the valve cover, too. For now, I used a long piece of 3/8 hoes inserted inside short pieces of 1/2 hose on both ends. Works fine, and the long hose is handy for removing the air cleaner housing.

Pushed the Jeep back outside, adjusted both Sol-Vac idle speeds:

To adjust the idle mixture on this carb, you have to use a Dwell meter hooked up the diagnostic port. It is supposed to read around 30 (orange scale). I can not get any better then 40. No amount of "in/out" on the mixture screw will get it any closer. I was able to dial in the old carburetor, but not this one?

I finally just leaned it in till is stumbled, backed it back out till it smoothed out, called it good, for now.
I also changed the engine oil and filter, and the air filter:

Oil just had the slightest tinge of "fuel" smell, and it was pretty black. Hopefully this latest oil change removed most of the old carbon/fuel that was in the engine/combustion chambers.
Swapped in new spark plugs, too. The white portions shows heavy contamination, the firing parts look clean:



Again, I am thinking all the carbon deposits are just excess washing out. This thing had been running stupid rich, now it is good, so hopefully it will be good to go. I'll check the plugs again after a couple hundred miles. Was glad to see no "oil fouling" present.
Installed 10mm flat washers over the 3/8" studs, 3/8 nylock nuts on the studs to secure the lock in hubs.

Those studs do flash rust easy, a bit of paint on the ends will clean them up. I used nylock nuts in case JeepAddict or some future owner wanted to remove the lock in hubs in the near future for some reason. Nylocks could also be a good long term solution???

Finally installed/hooked up the PCV fresh air hose components on the rear of the valve cover, too. For now, I used a long piece of 3/8 hoes inserted inside short pieces of 1/2 hose on both ends. Works fine, and the long hose is handy for removing the air cleaner housing.

Pushed the Jeep back outside, adjusted both Sol-Vac idle speeds:

To adjust the idle mixture on this carb, you have to use a Dwell meter hooked up the diagnostic port. It is supposed to read around 30 (orange scale). I can not get any better then 40. No amount of "in/out" on the mixture screw will get it any closer. I was able to dial in the old carburetor, but not this one?

I finally just leaned it in till is stumbled, backed it back out till it smoothed out, called it good, for now.
I also changed the engine oil and filter, and the air filter:

Oil just had the slightest tinge of "fuel" smell, and it was pretty black. Hopefully this latest oil change removed most of the old carbon/fuel that was in the engine/combustion chambers.
Swapped in new spark plugs, too. The white portions shows heavy contamination, the firing parts look clean:



Again, I am thinking all the carbon deposits are just excess washing out. This thing had been running stupid rich, now it is good, so hopefully it will be good to go. I'll check the plugs again after a couple hundred miles. Was glad to see no "oil fouling" present.
Installed 10mm flat washers over the 3/8" studs, 3/8 nylock nuts on the studs to secure the lock in hubs.

Those studs do flash rust easy, a bit of paint on the ends will clean them up. I used nylock nuts in case JeepAddict or some future owner wanted to remove the lock in hubs in the near future for some reason. Nylocks could also be a good long term solution???




















I would think the injectors, even with the pulse width turned to super short, would be too big for the 2.5 liter engines?? I could be wrong, but does anyone (Holley/Howell/etc.) market their systems toward the four cylinder engines? I have never noticed??
I wondered if you could swap the YJ TBI system on to the AMC four cylinder CJ engines?? Like, swap the entire intake from the YJ to the CJ?? Not sure, would be interesting 


































